front

Just wondering if anyone as a good how-to on how to remove and replace the front wheel? Putting new rotors on and don't want to get stuck halfway through. Can anyone verify the size of the front wheel nut for me? I was thinking of getting this tool (Ducati 28mm front axle nut socket) to do...

So, I thought a bulb had burnt out as my turn signal on the right was fast blinking. I noticed the front signal didn't work. So, instead of searching for a bulb I bought the NRC led black out lights. Installed them and it still does not work! So, I am looking for the location of the flasher...

I'm not sure if this applies to the Hyperstrada, but it's worth taking a look. So basically... I noticed rock chips on my fork stanchions... Yes, the slidy part that is supposed to be really smooth. The fork is supposed to have a protector or guard that keeps rocks from flying up from...

..and hopfully fixing the 'double pump' requirement on the M/C.. I'm no stranger to bleeding brakes, but have never worked with an ABS system before. Has anyone that has done this worked according to the manual or have you found more effective method(s)? Also, have you found a way to fix...

A guy in a car just pulled up next to me and mentioned it to me. Upon pulling over and testing I find that pulling the front brake lever no longer activates the brake light. The rear brake still activates it properly though. So, before I give myself a heart attack looking at the...

Hey all, So, my bike had been parked for the past 2 months. During that time, I installed a 14T front sprocket in anticipation of riding again. However, now I have run into a problem that has got me puzzled. My bike is intermittently redlining at 8000RPM. I have never even once had this...

Anybody replaced their fork seals? My right fork is weeping so am about to change them out as soon as I receive the parts I ordered. The manual I bought a couple of years ago talks about how to remove the forks but offers no explanation of replacing the seals. Does anyone have a link...

Hi all, this topic is spinning in my head since morning and I wanted to know if anyone was trying to get this babe back high as on Hypermotard? Original hypestrada comes with settings where the 43mm inverted Showa fork on has reduced wheel travel (from 6.7 down to 5.9 inches, ostensibly to...

Hi, I have to replace left hand guard with flasher, I bought new and it come with flasher cable with clip connector. Problem I have I need aces to the female connector and this is only possible if I remove all front, light .. the whole thing .. front fender. I try today but I didn't succeed...

I've had problems with my front brake. It required a couple of pumps to get a good feel. So whilst the Hyper was in for the 1st service I asked them to take a look. They bleed the brakes but in the end have ordered me a new master cylinder.

I am offering this new product rthat comes in two versions, 70 LED (35 LED each side) 140 LED (70 LED each side) They fit in the factory handguards and have a perfect fit to the curvature of the handguard. I understand that other products require black silicone around the seams. Mine don't...

Just out of interest I've had all the panels off my bike"¦..wanted to have a look and was also looking to route a usb cable from the under tank power socket to just below the control screen. Must admit I was surprised at what fuses are in the front fuse box and what had to be removed to get...

'Lo guys. I was just wondering: is the front mudguard long enough to keep debris/water/mud etc. from your engine/radiator/exhaust pipe etc.? I mean, my 996 scoops up quite a lot of water...and the HS/HM have an even shorter one. As far as I can tell, there are no extended versions nor...

I'm going to flush the fluid on my front brakes - I'll be putting on speed bleeders to help with this. I have a couple of questions: The manual calls for removing the calipers and forcing the pads apart to seat the pistons. It's unclear but I guess you bolt them back on after this process...

Ducati genuine carbon fiber front fairing - $200 shipped in the CONUS. Includes all mounting hardware. Fits all Hypermotards and Hyperstradas.

Can anyone confirm if these are the same as the stock connetors for the front turn signals? There's a C32-C (below) or a C70-C connector available. Ducati - 2 way connector kit for indicator lights | eBay Want to switch out my turn signals when I change the handguards however I don't...

i noticed the forks stick up quite a bit above the triple tree. where can i find the stock setting for this so i can double check all is good? and has anyone decreased or increased that measurement and results? thanks

Hi all. I'm looking to replace the hand guards, find them a bit ugly. So I want to move the front indicators elsewhere. Thinking about some Rizoma parts (Rizoma Billet motorcycles parts from Italy.) but wonder where best to mount them to keep it UK road legal.

Hi all. I don't like the standard front mudguard, thinking of putting the one from the Hyper on it or taking it off entirely. Anyone done this? Only issue I can think of is running the brake lines.

Like many of us not happy with the front end bounce. got my Racetech tuner to put .85 springs and gold valves for comp and rebound with a much improved feeling from the front. The bounce back over anything not smooth was still there. Then remembered my 07 Multi, same issue. most of the hand...