What'd you do to your Hyperstrada today?

Cyklnut · Oct 4, 2014

Strada Mods

Just purchased my Hyperstrada. Added a rack to the tail which I purchased from Altrider, and a front fender extension which I purchased from Motomachines. Took the Strada out Wednesday for a 400m run and all is well. Lov my new Strada.

dragoontwo · Oct 4, 2014

TitoZilla said:
How are those Samco hoses performing? Do you notice a difference in running temperature?

How are the mirrors over stock? Are they wider?

Could you show more pics of the Rizoma rear end action? Mostly the turn signal jibbers. I am trying to figure out a tail tidy to fit with my givi top case rack.

Not exactly sure how much of a difference there is in temps. I got them for free.

The rear end is not Rizoma. You can find out more about it starting here.

twozzie · Oct 6, 2014

jerdog53 said:
So a few addition to the Strada over the weekend

Added the DP off road hand guards

These units are LED opposed to the incandescent bulbs found in the stockers.

These are full on aluminum guards just like they should be.

Jerdog, what is the part for these hand guards? I cant find anything on the Ducati site

jerdog53 · Oct 7, 2014

I got them from Pro Italia in SoCal.

http://store.proitalia.com/ducati-hypermotard-hyperstrada-off-road-hand-guard-kit

niiico · Oct 10, 2014

I installed frame sliders from espritmotorcycle (ebay)

I was unable to mount the provided nuts since my wrenches were too large to go inside the hole of the slider. Had to buy a genuine ducati nut which is narrower...

They look good. I just expect they won't bend the frame in case of crash, because they are very long.

gatdammit · Oct 10, 2014

I like those better than the Speedymoto's because you can use them as relief foot-pegs on longer trips.

TitoZilla · Oct 10, 2014

I want to see more of this up close! Pretty please.

zippy49 · Oct 10, 2014

Cyklnut said:
Just purchased my Hyperstrada. Added a rack to the tail which I purchased from Altrider, and a front fender extension which I purchased from Motomachines. Took the Strada out Wednesday for a 400m run and all is well. Lov my new Strada.

They only list one for the Hypermotard, which has a different front fender. They do not show one installed,either. Pic, please?

crbiker · Oct 23, 2014

Givi E340NT and auxiliary led lights from super bright leds . com

Joecati · Oct 23, 2014

frank33m said:
So far I've added EvoTech radiator and head guards , AltRider water pump guard and rear rack , Speedymoto frame and axle sliders , Shorty mirror ,Competition Werks slip-on ,Bead Rider seat beads , Fender eliminator with smaller rear T/S and the Givi case . I also removed the charcoal canister , the big ugly mirrors , and the saftey decals and reflectors.

Frank, what are those clip things on the lower front section of the exhaust pipe, where did you get them?

Monstard · Oct 28, 2014

installed puig screen

the puig screen i ordered was waiting for me after coming back from a trip. so i installed it today, good quality. i especially like the support bracket. screen feels solid, doesn't flex like the oem without it

arnonag · Oct 28, 2014

panniers

Monstard said:
the puig screen i ordered was waiting for me after coming back from a trip. so i installed it today, good quality. i especially like the support bracket. screen feels solid, doesn't flex like the oem without it

Nice screen. on the photos i could see your panniers. what make are they ?

ambientscape · Oct 28, 2014

Hey monstard, u lowered quite a lot on your front fork.

Monstard · Oct 28, 2014

arnonag said:
Nice screen. on the photos i could see your panniers. what make are they ?

it's a Givi E22 side case. saw a fellow member here post a photo a similar set-up so i just followed. it required a bit of modification, though. more info HERE

ambientscape said:
Hey monstard, u lowered quite a lot on your front fork.

yep, i pulled the forks up the triples and that's as low as it gets. but with barely 30-inch inseam, i still can't flat-foot the bike

typical asian legs

Pabst · Nov 18, 2014

I replaced my brake and clutch levers with adjustable ones, got them on ebay for $40, very nicely made and only takes about ten minutes to change them, makes all the difference in the world, I can ride with two fingers on each, the stock ones make the reach difficult, especially with gloves.

b9009b · Nov 18, 2014

Spilled gas all over it filling it up rode back home and washed it in 21 degree weather. Hands are still frozen.

Joecati · Dec 8, 2014

Monstard said:
the puig screen i ordered was waiting for me after coming back from a trip. so i installed it today, good quality. i especially like the support bracket. screen feels solid, doesn't flex like the oem without it

Any chance you have time to post a picture holding the stock windscreen up against your puig to show difference in size/shape?

Monstard · Dec 9, 2014

Joecati said:
Any chance you have time to post a picture holding the stock windscreen up against your puig to show difference in size/shape?

sure thing... we're in the middle of a typhoon right now. hopefully the weather let's up tomorrow

silenthunter · Dec 9, 2014

@ joecati

Herr are some pics, with the dark screen

http://hyperstrada.com/gear/755-puig-touring-screen-2.html

Monstard · Dec 16, 2014

Joecati said:
Any chance you have time to post a picture holding the stock windscreen up against your puig to show difference in size/shape?

here you go

What'd you do to your Hyperstrada today?

Help Support Hypermotard Forum:

New Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Attachments

Well-Known Member

Well-Known Member

Attachments

Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads